Custom Battery Packs Built for Real Operating Loads
Six custom battery architectures engineered for US, UK, European, and ANZ equipment makers. Client names stay confidential under NDA, while all electrical parameters, CAD layouts, and test records come directly from our engineering builds.


30+ Months of Continuous Multi-SKU OEM Production, Including Non-Standard 16V Marine Packs
Challenge
A U.S. marine lithium brand needed one factory for both standard private-label SKUs and a non-standard 16V (5S LFP) pack for marine electronics. Larger factories turned away the 16V build because it sat outside standard 12V and 24V lines.
Ingénierie & Production
We built a 5S9P 16V 135Ah pack (12V to 18.2V window) with UL-recognized 32140 LFP cells alongside their 12.8V, 24V, and 36V lineup. Incoming cell lots pass capacity and IR grading prior to welding, and serialized batch records tie every pack to its cell lot, BMS batch, and EOL test sheet.
Delivery Record
Moved from sample sign-off in April 2023 to a 175-pack initial batch in May 2023, followed by over 30 consecutive months of repeat shipments.

25.6V 75Ah Low-Profile AGV & Robotics Pack Verified for 150A Continuous and 200A Pulse Loads
Challenge
Warehouse AGVs and mobile robots draw sharp current spikes during acceleration and heavy lifting. Standard 1C LFP packs suffer voltage sag under 2C to 3C pulses, causing BMS trips and mid-shift controller reboots inside tight chassis bays.
Ingénierie & Validation
We engineered a slim 76mm-tall 8S5P 32140 LFP pack using low-impedance busbars, 6 AWG power leads, and an Anderson 170A interface with dedicated communication wiring. The BMS curve was tuned for 150A continuous load, 200A 3-second peaks, and a 250A over-current cutoff paired with a matched 29.2V charger.
Outcome
Held stable bus voltage across repeated high-current starts without increasing pack footprint or adding external capacitor banks.

12V 50Ah Sodium-Ion Pack Built for Sub-Zero Operation Without Internal Heating Pads
Challenge
Standard LiFePO4 packs cannot charge below 0°C without lithium plating risk. In Alpine and Nordic equipment, internal heating pads drain usable energy before work starts and add relays and thermistors that can fail in winter field service.
Engineering Solution
We built a 4S5P 12V 50Ah sodium-ion pack using NaCR33140 cells backed by cell-level cold-temperature test reports. Because sodium-ion handles sub-zero charging across an 8.0V to 15.6V window, the pack runs without resistive heaters and tolerates zero-volt storage safely.
Outcome
Gave European outdoor and remote power equipment builders a simpler cold-climate drop-in option with higher net winter runtime.

64.8V 50Ah (3.24 kWh) High-Density NMC Pack for Heavy-Lift Commercial Drones
Challenge
Heavy-payload UAVs need a 64.8V bus to cut motor current and harness weight, plus 1C fast charging between flights. Any cell mismatch inside an 18S10P stack shortens flight endurance and creates hot spots during rapid turnaround charging.
Engineering Solution
We assembled an 18S10P pack (417 x 237 x 78 mm) from Samsung 21700 5000mAh NMC cells tightly sorted by OCV and internal resistance. Interconnect paths were balanced across all 18 series groups to sustain 60A flight loads and 50A fast charging.
Outcome
Delivered 3.24 kWh in a compact high-voltage architecture built for long-endurance aerial survey and industrial UAS platforms.

46.8V 5Ah Removable Pack Engineered Into a 22mm Slim L-Shape Cavity
Challenge
A U.S. hardware team developing a cordless commercial display needed a removable 46.8V pack inside an irregular 22mm-thick L-shape bay. Standard BMS boards and cell holders exceeded the clearance, and launch testing left no window for enclosure re-tooling.
Ingénierie & Delivery
We arranged 13S1P EVE 21700 5000mAh cells into the exact L-shape footprint and tucked the compact BMS into the shoulder clearance while keeping full electrical creepage margins and 65°C cutoff protection. Engineering samples and pilot batches shipped by dangerous-goods air express across consecutive months.
Outcome
Kept U.S. hardware validation on schedule with zero changes to the client’s outer chassis tooling.

51.2V 230Ah (11.77 kWh) Prismatic LFP System with Matched 1.2kW DC-DC Charging
Challenge
Commercial fleet and off-grid integrators frequently hit inrush trips when pairing high-capacity 51.2V LFP packs with vehicle DC-DC converters, alongside strict hazmat sea-freight inspections at destination ports.
Ingénierie & Delivery
We built a serviceable metal enclosure around REPT 230Ah prismatic cells with lifting eyebolts and front-access BMS terminals. Before shipment, we bench-matched the 1.2kW DC-DC charger to the pack BMS curve and issued serialized EOL capacity reports with complete UN38.3 ocean-freight documentation.
Outcome
Cleared customs without delay and entered commercial field service, extending a multi-year supply partnership from 2024 through 2026.
Have an Equipment Spec Ready? Send It to Our Engineering Team.
We work with US, European, UK, and ANZ equipment makers planning 100 to 5,000 packs per year, plus specialized industrial programs needing custom BMS tuning, IP68 protection, or UN38.3, IEC, and UL documentation. Mutual NDAs are signed within 2 hours.
Include These Details for an 8-Hour Feasibility Review
- Target equipment and operating environment
- Nominal voltage and capacity or runtime goal
- Continuous and peak discharge current profile
- Enclosure dimensions and IP rating target
- Required certifications (UN38.3, IEC, UL) and annual volume